Home UP BOARD Question Papers NCERT Solutions Sample Papers CBSE Notes NCERT Books CBSE Syllabus

Class 11 Physics NCERT Solutions For Chapter 10 Mechanical Properties of Fluids

mechanical properties of fluids class 11 ncert solutions, ncert, ncert physics, physics ncert, cbse ncert, ncert questions, ncert cbse, ncert s, ncert class 4, ncert test, ncert ncert, ncert class 2, ncert schools , ncert solutions, chapter 10,chapter 10ncert solutions, mechanical properties of fluids ncert solutions, ncert solutions for class 11 physics, class 11 physics ncert solutions, ncert solutions for class 11, ncert class 11 physics, class 11 physics, class 11 physics solution, ncert solutions class 11, class 11 physics , ncert class 11, class 11 physics chapter 10,chapter 10 mechanical properties of fluids ncert solutions

Chapter 10 Mechanical Properties Of Fluids

Download NCERT Solutions for Class 11 physics

(Link of Pdf file is given below at the end of the Questions List)

In this pdf file you can see answers of following Questions

NCERT Solutions Exercises Questions

Question 10.1 Explain why (a) The blood pressure in humans is greater at the feet than at the brain (b) Atmospheric pressure at a height of about 6 km decreases to nearly half of its value at the sea level, though the height of the atmosphere is more than 100 km (c) Hydrostatic pressure is a scalar quantity even though pressure is force divided by area.

Question 10.2 Explain why (a) The angle of contact of mercury with glass is obtuse, while that of water with glass is acute. (b) Water on a clean glass surface tends to spread out while mercury on the same surface tends to form drops. (Put differently, water wets glass while mercury does not.) (c) Surface tension of a liquid is independent of the area of the surface (d) Water with detergent disolved in it should have small angles of contact. (e) A drop of liquid under no external forces is always spherical in shape

Question 10.3 Fill in the blanks using the word(s) from the list appended with each statement:
(a) Surface tension of liquids generally . . . with temperatures (increases / decreases)
(b) Viscosity of gases . .. with temperature, whereas viscosity of liquids . . . with temperature (increases / decreases) (c) For solids with elastic modulus of rigidity, the shearing force is proportional to . . . , while for fluids it is proportional to . .. (shear strain / rate of shear strain)
(d) For a fluid in a steady flow, the increase in flow speed at a constriction follows (conservation of mass / Bernoulli’s principle)
(e) For the model of a plane in a wind tunnel, turbulence occurs at a ... speed for turbulence for an actual plane (greater / smaller)

Question 10.4 Explain why
(a) To keep a piece of paper horizontal, you should blow over, not under, it
(b) When we try to close a water tap with our fingers, fast jets of water gush through the openings between our fingers (c) The size of the needle of a syringe controls flow rate better than the thumb pressure exerted by a doctor while administering an injection
(d) A fluid flowing out of a small hole in a vessel results in a backward thrust on the vessel
(e) A spinning cricket ball in air does not follow a parabolic trajectory

Question 10.5 A 50 kg girl wearing high heel shoes balances on a single heel. The heel is circular with a diameter 1.0 cm. What is the pressure exerted by the heel on the horizontal floor ?

Question 10.6 Toricelli’s barometer used mercury. Pascal duplicated it using French wine of density 984 kg m–3. Determine the height of the wine column for normal atmospheric pressure.

Question 10.7 A vertical off-shore structure is built to withstand a maximum stress of 109 Pa. Is the structure suitable for putting up on top of an oil well in the ocean ? Take the depth of the ocean to be roughly 3 km, and ignore ocean currents.

Question 10.8 A hydraulic automobile lift is designed to lift cars with a maximum mass of 3000 kg. The area of cross-section of the piston carrying the load is 425 cm2. What maximum pressure would the smaller piston have to bear ?

Question 10.9 A U-tube contains water and methylated spirit separated by mercury. The mercury columns in the two arms are in level with 10.0 cm of water in one arm and 12.5 cm of spirit in the other. What is the specific gravity of spirit ?

Question 10.10 In the previous problem, if 15.0 cm of water and spirit each are further poured into the respective arms of the tube, what is the difference in the levels of mercury in the two arms ? (Specific gravity of mercury = 13.6)

Question 10.11 Can Bernoulli’s equation be used to describe the flow of water through a rapid in a river ? Explain.

Question 10.12 Does it matter if one uses gauge instead of absolute pressures in applying Bernoulli’s equation ? Explain.

Question 10.13 Glycerine flows steadily through a horizontal tube of length 1.5 m and radius 1.0 cm. If the amount of glycerine collected per second at one end is 4.0 × 10–3 kg s–1, what is the pressure difference between the two ends of the tube ? (Density of glycerine = 1.3 × 103 kg m–3 and viscosity of glycerine = 0.83 Pa s). [You may also like to check if the assumption of laminar flow in the tube is correct].

Question 10.14 In a test experiment on a model aeroplane in a wind tunnel, the flow speeds on the upper and lower surfaces of the wing are 70 m s–1and 63 m s-1 respectively. What is the lift on the wing if its area is 2.5 m2 ? Take the density of air to be 1.3 kg m–3.

Question 10.15 Figures10.23(a) and (b) refer to the steady flow of a (non-viscous) liquid. Which of the two figures is incorrect ? Why ?

Question 10.16 The cylindrical tube of a spray pump has a cross-section of 8.0 cm2 one end of which has 40 fine holes each of diameter 1.0 mm. If the liquid flow inside the tube is 1.5 m min–1, what is the speed of ejection of the liquid through the holes ?

Question 10.17 A U-shaped wire is dipped in a soap solution, and removed. The thin soap film formed between the wire and the light slider supports a weight of 1.5 × 10–2 N (which includes the small weight of the slider). The length of the slider is 30 cm. What is the surface tension of the film ?

Question 10.18 Figure 10.24 (a) shows a thin liquid film supporting a small weight = 4.5 × 10–2 N. What is the weight supported by a film of the same liquid at the same temperature in Fig. (b) and (c) ? Explain your answer physically

Question 10.19 What is the pressure inside the drop of mercury of radius 3.00 mm at room temperature ? Surface tension of mercury at that temperature (20 °C) is 4.65 × 10–1 N m–1. The atmospheric pressure is 1.01 × 105 Pa. Also give the excess pressure inside the drop.

Question 10.20 What is the excess pressure inside a bubble of soap solution of radius 5.00 mm, given that the surface tension of soap solution at the temperature (20 °C) is 2.50 × 10–2 N m–1 ? If an air bubble of the same dimension were formed at depth of 40.0 cm inside a container containing the soap solution (of relative density 1.20), what would be the pressure inside the bubble ? (1 atmospheric pressure is 1.01 × 105 Pa). Additional Exercises

Question 10.21 A tank with a square base of area 1.0 m2 is divided by a vertical partition in the middle. The bottom of the partition has a small-hinged door of area 20 cm2. The tank is filled with water in one compartment, and an acid (of relative density 1.7) in the other, both to a height of 4.0 m. compute the force necessary to keep the door close.

Question 10.22 A manometer reads the pressure of a gas in an enclosure as shown in Fig. 10.25
(a) When a pump removes some of the gas, the manometer reads as in Fig. 10.25 (b) The liquid used in the manometers is mercury and the atmospheric pressure is 76 cm of mercury. (a) Give the absolute and gauge pressure of the gas in the enclosure for cases (a) and (b), in units of cm of mercury. (b) How would the levels change in case (b) if 13.6 cm of water (immiscible with mercury) are poured into the right limb of the manometer ? (Ignore the small change in the volume of the gas).

Question 10.23 Two vessels have the same base area but different shapes. The first vessel takes twice the volume of water that the second vessel requires to fill upto a particular common height. Is the force exerted by the water on the base of the vessel the same in the two cases ? If so, why do the vessels filled with water to that same height give different readings on a weighing scale ?

Question 10.24 During blood transfusion the needle is inserted in a vein where the gauge pressure is 2000 Pa. At what height must the blood container be placed so that blood may just enter the vein ? [Use the density of whole blood from Table 10.1].

Question 10.25 In deriving Bernoulli’s equation, we equated the work done on the fluid in the tube to its change in the potential and kinetic energy.
(a) What is the largest average velocity of blood flow in an artery of diameter 2 × 10–3 m if the flow must remain laminar ?
( b) Do the dissipative forces become more important as the fluid velocity increases ? Discuss qualitatively.

Question 10.26 (a) What is the largest average velocity of blood flow in an artery of radius 2×10–3m if the flow must remain lanimar?
(b) What is the corresponding flow rate ? (Take viscosity of blood to be 2.084 × 10–3 Pa s).

Question 10.27 A plane is in level flight at constant speed and each of its two wings has an area of 25 m2. If the speed of the air is 180 km/h over the lower wing and 234 km/h over the upper wing surface, determine the plane’s mass. (Take air density to be 1 kg m–3).

Question 10.28 In Millikan’s oil drop experiment, what is the terminal speed of an uncharged drop of radius 2.0 × 10–5 m and density 1.2 × 103 kg m–3. Take the viscosity of air at the temperature of the experiment to be 1.8 × 10–5 Pa s. How much is the viscous force on the drop at that speed ? Neglect buoyancy of the drop due to air.

Question 10.29 Mercury has an angle of contact equal to 140° with soda lime glass. A narrow tube of radius 1.00 mm made of this glass is dipped in a trough containing mercury. By what amount does the mercury dip down in the tube relative to the liquid surface outside ? Surface tension of mercury at the temperature of the experiment is 0.465 N m–1. Density of mercury = 13.6 × 103 kg m–3.

Question 10.30 Two narrow bores of diameters 3.0 mm and 6.0 mm are joined together to form a U-tube open at both ends. If the U-tube contains water, what is the difference in its levels in the two limbs of the tube ? Surface tension of water at the temperature of the experiment is 7.3 × 10–2 N m–1. Take the angle of contact to be zero and density of water to be 1.0 × 103 kg m–3 (g = 9.8 m s–2

Please Wait pdf file is loading (कृपया इंतजार करें pdf file लोड हो रही है)...
Loading speed will depend up on your download speed. Pdf file के लोड होने में लगा समय आपकी डाउनलोड स्पीड पर निर्भर करेगा

Loading document ...
Loading page ...

Download pdf file links for Mechanical Properties Of Fluids Class 11 NCERT Solutions

To download above pdf file Link is given below.
उपर दिखायी दे रही पीडीऍफ़ को डाउनलोड करने का लिंक नीचे दिया गया है

Important Links

NCERT CBSE Notes Class 6 - 12 Download pdf

Ncert Solution for class 6 to 12 download in pdf

CBSE Model test papars Download in pdf

NCERT Books for Class 1- 12 Hindi & English Medium

Mathematics Biology Psychology
Chemistry English Economics
Sociology Hindi Business Studies
Geography Science Political Science
Statistics Physics Accountancy

CBSE Syllabus Class 9 to 12 Year 2021-22

Last year CBSE Question paper

Important Links

Follow Us On

Face book page ncerthelp twitter page youtube page linkdin page

Solved Last Year Question Paper

If You have any problem/query related to above page please send us your Query to [email protected] with code Serial No1518/1106. Thanks

Please Share this webpage on facebook, whatsapp, linkdin and twitter.

Facebook Twitter whatsapp Linkdin

Copyright @ ncerthelp.com A free educational website for CBSE, ICSE and UP board.